Audiovox PRO-9056 User Manual download pdf

128-7762

1 of 19

The selectable features can be set manually as explained below, or with the RF feature programmer.

To set features using the RF programmer, follow the instructions packaged with the programmer.

Factory default settings are indicated by bold text.

Note : The method of manual override can either be selected to operate from the valet switch or operate as custom code.

Be certain to place a check mark indicating the method used in the box located on the last page of the owner's manual.

NOTE: Keyless Entry Models with no horn output will Flash the Parking Lights instead of chirp where chirp is indicated.

Also, No data will be indicated if a feature is not available for a particular model. The unit will enter the feature but no selection will be available.

RF Programmable Feature Bank 1 Is For Transmitter Programming See Transmitter Programming Guide.

RF Programmable Features Bank 2 Is Alarm Selectable Features:

Feature Selection 1 Chirp 2 Chirps 3 Chirps 4 Chirps 5 Chirps 6 Chirps

1st DoorL/UL 1 Sec. 3.5 Sec. 1 Sec L, Dbl. U/L Dbl L, 1 Sec UL Dbl L, Dbl UL 1 S l/350mS ul

2nd Accy Lock Not Available

3rd Accy. UL Not Available

4th Headlights Not Available

5th Passive Locks Not Available

6th Pass/Act Arm Not Available

7th Siren/Horn Not Available

8th Horn Chirp Not Available

9th O/R Method Not Available

10th 2 Step U/L Not Available

11th Chp Del Tx Not Available

12th Voltage/Hd Wire Not Available

13th Trigger Circuits Not Available

14th Lock/Unlock Poll Not Available

15th Aux Ch 5 Sel Not Available

16th Aux Ch 6 Sel Not Available

17th Aux Ch 7 Sel Not Available

18th Trigger Delay Not Available

When using the RF programmer, enter the program mode as follows:

Turn the ignition on

Press and release valet switch 3 times

turn ignition off then on

Press and hold valet switch for 5 seconds

Siren and or lights chirp/flash 2 times indicating access to RF feature program mode.

Model PRO-9056

Installation Manual

1 2 3 4 5 6 ... 18 19

Summary of Contents

Page 1 - Model PRO-9056

128-77621 of 19The selectable features can be set manually as explained below, or with the RF feature programmer.To set features using the RF programm

Page 2

128-776210 of 19the applications described below, a relay will be required. The Light Blue wire can be used to accommodate thefollowing situations:A.

Page 3

128-776211 of 19cases will operate properly from one multi coil pack regardless of the number of cylinders. If the vehicle has asingle coil unit for

Page 4

128-776212 of 192 Pin Transponder Control Output: (Yellow Connector)This output is intended to allow the control of a transponder bypass interface mod

Page 5

128-776213 of 19columns. The Green/Black wires should be connected to the negative (-) terminal of the respective cylindernumber which appears in any

Page 6

128-776214 of 191. Set the vehicle parking brake.2. Block the drive wheels to prevent vehicle movement.3. Temporarily disconnect the Brown/Black pos

Page 7

128-776215 of 19AUDIOVOX ADVISES THAT YOU MAINTAIN THE FACTORY CIRCUIT WHENEVER POSSIBLE. The following twocircuits may be used only if the above cir

Page 8

128-776216 of 19C. Locate the key in sensor switch wire that connects the chime module to the ignition cylinder .D. Cut this wire and connect the igni

Page 9

128-776217 of 19

Page 10 - 10 of 19

128-776218 of 19THIS PAGE LEFT BLANK INTENTIONALLY

Page 11 - 11 of 19

Page 12 - 12 of 19

128-77622 of 19To program these selectable features;Action System ResponseTurn ignition on No responsePress and release the valet switch 3 times 1 Ch

Page 13 - 13 of 19

128-77623 of 19To exit program mode, turn ignition off, or press and release valet switch.RF Programmable Features Bank 3 Is Remote Start Selectable F

Page 14 - 14 of 19

128-77624 of 19Action System ResponseTurn ignition on No responsePress and release the valet switch 3 times 1 Chirp - LED 1 flashWithin 3 seconds, tu

Page 15 - 15 of 19

128-77625 of 19This Remote Start System is designed for use with Automatic Transmission Vehicles Only! The unit provideswait to start input for glow

Page 16 - 16 of 19

128-77626 of 19IMPORTANT!DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MULTI PIN INPUT / OUTPUT HARNESS INTO THECONTROL MODULE UNTIL ALL CONNECTIO

Page 17 - 17 of 19

128-77627 of 19SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.BLUE WIRE: Ignition 1 OutputConnect this wire to the ignition 1 wire from the ignitio

Page 18 - 18 of 19

128-77628 of 19VIOLET WIRE: Accessory OutputConnect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the

Page 19 - 19 of 19

128-77629 of 19Brake Switch Positive Shutdown DetailYELLOW w/ BLACK Tracer Wire: + 12 Volt Alarm By - Pass OutputNOTE: You must disconnect the igni