Audiovox AMP-590A Owner's Manual download pdf (Page 26)



ENGLISH

Getting Started Connections Playback Remote Control Information Troubleshooting Speciﬁcations

Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)

This is displayed after the Audyssey Auto Setup procedure is

completed.

Even if the settings are changed after the Audyssey Auto Setup

procedure, the Audyssey Auto Setup settings can be restored by

selecting “Restore” then pressing .

 Press ui to select

“Parameter Check”,

then press .

“Parameter Check” is

displayed on the on-screen

display.



Use ui to select the item you want to check, then

press .

Speaker Conﬁg. Check

: Check the speaker conﬁguration

Distance Check

: Check the distance

Channel Level Check

: Check the channel level

Crossover Freq. Check

: Check the crossover frequency

EQ Check

: Check the equalizer



Use o p to switch the display between the different

speakers.



Press .

The conﬁrmation screen reappears. Repeat steps 2 and 3.

Check Audyssey Auto Setup

Measurement Results (Parameter Check)

3-2.Parameter Check

Speaker Config.Check

Distance Chenck

Channel Level Check

Crossover Freq.Check

Restore

EQ Check

[ENT]:Select [RTN]:Back

Error messages (examples) Cause Measures

Retry

Cancel

[ENT]:Retry

Microphone:None

Speaker :None

Caution

MultEQ

• Included setup microphone is not connected.

• Not all speakers could be detected.

• The front L speaker was not properly detected.

• Connect the included setup microphone to the

SETUP MIC jack on the main unit.

• Check the speaker connections.

too high or

Retry

Cancel

[ENT]:Retry

Ambient noise is

Level is too low.

Caution

MultEQ

• Too much noise in the room for accurate

measurements to be made.

• Speaker or subwoofer sound is too low for

accurate measurements to be made.

• Either turn off any device generating noise or

move it away.

• Try again when the surroundings are quieter.

• Check the speaker installation and the direction

in which the speakers are facing.

• Adjust the subwoofer’s volume.

Retry

R :None

Cancel

Skip

Front

Caution

[ ]:Up/Down [ ]:CH

MultEQ

• Displayed speaker could not be detected.

· The front R speaker were not properly detected.

· Only one channel of the surround speakers was

detected.

· Sound was output from the R channel when only

one surround back speaker was connected.

· The surround back, but the surround speaker was

not detected.

• Check the connections of the displayed

speaker.

Retry

L :Phase

Cancel

Skip

Front

Caution

[ ]:Up/Down [ ]:CH

MultEQ

• Displayed speaker connected with the polarities

reversed.

• Check the polarities of the displayed speaker.

• For some speakers, this error message may

be displayed even if the speaker is properly

connected. If you are sure that the wiring is

correct, press ui to select “Skip”, then press

NOTE

Be sure to turn the power off before checking the speaker connections.

n To perform the Audyssey Auto Setup procedure again

Press ui to select “Retry”, then press .

n To cancel Audyssey Auto Setup

Use ui to select “Cancel”, then select “Yes” using o p.

Error Messages

If the Audyssey Auto Setup procedure could not be completed due to speaker installation, the measuring environment, etc., an error message is

displayed. If this happens, check the relevant items, be sure to take the necessary measures, then perform the Audyssey Auto Setup procedure

over again.

Settings

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 66 67

Comments to this Manuals

No comments

Audiovox AMP-590A Owner's Manual Page 26

Comments to this Manuals

Related products and manuals for Car audio amplifiers Audiovox AMP-590A