Audiovox Rampage AV-455 User Manual Page 9

  • Download
  • Add to my manuals
  • Print
  • Page
    / 12
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 8
128-5504128-5504
128-5504128-5504
128-5504
9 of 129 of 12
9 of 129 of 12
9 of 12
88
88
8
OPERATING INSTRUCTIONS / SETTING THE CLOCKOPERATING INSTRUCTIONS / SETTING THE CLOCK
OPERATING INSTRUCTIONS / SETTING THE CLOCKOPERATING INSTRUCTIONS / SETTING THE CLOCK
OPERATING INSTRUCTIONS / SETTING THE CLOCK
resume when the cassette is ejected.
NOTENOTE
NOTENOTE
NOTE
::
::
:Never leave a cassette engaged in the player
when not in use. Doing so can cause damage
to the cassette and/or mechanism of the unit.
Always press the eject button and remove the
cassette before removing the detachable front panel.
TAPE MODE SELECTOR (TAPE) TAPE MODE SELECTOR (TAPE)
TAPE MODE SELECTOR (TAPE) TAPE MODE SELECTOR (TAPE)
TAPE MODE SELECTOR (TAPE)
During radio operation, press this button to change to
tape play if a cassette is already loaded in the unit
( TAPE IN is shown on the display panel to indicate
that a tape is loaded).
  
  
 
TIME/FREQUENCY SELECTOR (T/F) TIME/FREQUENCY SELECTOR (T/F)
TIME/FREQUENCY SELECTOR (T/F) TIME/FREQUENCY SELECTOR (T/F)
TIME/FREQUENCY SELECTOR (T/F)
Press this button to call the time display on the
incorporated quartz clock. The display will return to
the normal indication (radio frequency or “TAPE”) after
5 seconds.
THEFT-DETERRENT L.E.D. THEFT-DETERRENT L.E.D.
THEFT-DETERRENT L.E.D. THEFT-DETERRENT L.E.D.
THEFT-DETERRENT L.E.D.
Located on the chassis behind the front panel, a light-
emitting diode (L.E.D.) will flash when the panel is
removed. The flashing light serves as a visual warning
to the would-be thief that the unit has been disabled by
removal of the front panel.
RE-SET BUTTON RE-SET BUTTON
RE-SET BUTTON RE-SET BUTTON
RE-SET BUTTON
A Re-Set button is located on the front of the chassis
(front panel must be removed to access the button).
The re-set circuitry is provided to protect the
microprocessor circuitry and should only be activated
under the following circumstances as it will erase the
time and pre-set memories.
1. Switch the vehicle ignition and radio "
onon
onon
on".
2. Momentarily press the Time/Frequency Selector button so that the time is shown on the display panel.
3. Within 5 seconds (while the time still appears on the display), press and hold the Time/Frequency Selector
and the Down Tuning (
) button to adjust the hours or the Up Tuning (
) button to adjust the minutes
to the correct time.
4. When the correct time is set, release the Time/Frequency Selector. After five seconds the display will
return to the normal indication.
SETTING THE CLOCKSETTING THE CLOCK
SETTING THE CLOCKSETTING THE CLOCK
SETTING THE CLOCK
1. Upon initial installation after all wiring is completed.
2. If there is a malfunction of any of the switches on
the unit, pressing the Re-Set button may clear the
system and return to normal operation.
FRONT PANEL RELEASE BUTTON (OPEN) FRONT PANEL RELEASE BUTTON (OPEN)
FRONT PANEL RELEASE BUTTON (OPEN) FRONT PANEL RELEASE BUTTON (OPEN)
FRONT PANEL RELEASE BUTTON (OPEN)
This button is used to release the mechanism that
holds the front panel to the chassis. To detach the
front panel, press the button so that the panel drops to
the lowered position. Grasp the panel at the middle
and pull it off of the chassis. After removing the panel,
push the metal plate back up to the vertical position.
To re-attach the panel, press it straight onto the
chassis until the mechanism locks it into place.
NOTES ON USE OF FRONT PANELNOTES ON USE OF FRONT PANEL
NOTES ON USE OF FRONT PANELNOTES ON USE OF FRONT PANEL
NOTES ON USE OF FRONT PANEL
1. Make sure the front panel is right-side-up when
attaching it to the chassis as it cannot be attached
when up-side down.
2. Do not press very hard on the front panel when
attaching it to the chassis. No more than light to
moderate pressure should be needed.
3. When attaching the front panel, make sure it is
centered in the chassis frame and is pressed
straight into position.
4. When taking the front panel with you, please use
the supplied carrying case to protect the panel
from dirt and damage. Make sure there is no dust
or dirt on the electrical terminals on the back of
the panel as this could cause intermittent operation
or other malfunctions.
Page view 8
1 2 3 4 5 6 7 8 9 10 11 12

Comments to this Manuals

No comments