Audiovox PRO-9056 User Manual download pdf (Page 5)

128-7762

5 of 19

This Remote Start System is designed for use with Automatic Transmission Vehicles Only! The unit provides

wait to start input for glow plug pre-heat which will be used for all diesel applications. If this wire is not

connected, then the unit will remain in the Gasoline mode setting, which will crank the car when the RF signal is

received with no delay. Regardless of the vehicle, Gasoline or Diesel, for every installation, the vehicle MUST

HAVE a Tach Signal Input, and an Automatic Transmission.

INSTALLATION OF THE MAJOR COMPONENTS:

CONTROL MODULE:

Select a mounting location inside the passenger compartment (up behind the dashboard). The mounting location

selected must be within 24" of the ignition switch wiring harness to allow connection of the 6 pin main wiring

harness.

Be certain that the chosen location will not interfere with proper operation of the vehicle. Avoid mounting the

module to or routing the wiring around the steering shaft/column, as the module or wiring may wrap around or

block the steering wheel preventing proper control of the vehicle. Secure the module in the chosen location using

cable ties or screws as necessary.

NOTE: Do Not Mount The Module In The Engine Compartment, as it is not waterproof.

HOOD PIN SWITCH:

The hood pin switch included in this package is required for the safety shut down of the remote start unit. If the

vehicle is being worked on, this hood switch prevents the remote start activation even if the RF command to start

is issued. This hood pin switch MUST be installed in all applications. Failure to install the hood pin switch may

result in personal injury or property damage. Mount the hood pin switch in an area under the hood that is away from

water drain paths. If necessary, the included brackets may be used to move the hood pin switch away from rain

gutters or allow mounting to the firewall behind the hood seal. In either case the hood pin switch must be set up

to allow the hood to depress the switch at least 1/4" when the hood is closed and fully extended when the hood is

opened. For direct mounting, a 1/4" hole must be drilled. Carefully check behind the chosen location to insure the

drill will not penetrate any existing factory wiring or fluid lines. Drill a 1/4" hole in the desired location and thread the

hood pin switch into it using a 7/16" nut driver or deep well socket. If using the mounting bracket, first secure the

bracket to the desired location and secure the hood pin switch in the pre-threaded mounting bracket hole.

PUSH-BUTTON LED SWITCH

Select a mounting location known and accessible to the operator of the vehicle. A dash knockout plug or front dash

panel is desirable as the now Push-Button LED assembly needs the LED to be visible from the outside of the

vehicle and will be used for valet modes, programming features, programming transmitters, and for overriding the

remote start unit when the vehicle is being serviced. Inspect behind the chosen location to insure that adequate

clearance is allowed for the body of the switch, and also that the drill will not penetrate any existing factory wiring or

fluid lines. Drill a 5/16" or 8mm hole in the desired location and mount the switch by passing the connectors, one

at a time, through the panel from the front side and pressing on the bezel until the switch is fully seated.

This system is to be used in vehicles with AUTOMATIC TRANSMISSIONS only! Although this combination Keyless

Entry/Remote Start unit is a sophisticated system with many advanced features, IT MUST NOT be installed into a

vehicle with a manually operated transmission. Doing so may result in serious personal injury and property damage.

THE RECEIVER/ANTENNA ASSEMBLY:

The Superheterodyne Receiver Antenna Assembly provided with this unit allows routing from below the dashboard

for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception.

Special considerations must be made for windshield glass as some newer vehicles utilize a metallic shielded

window glass that will inhibit or restrict RF reception. In these vehicles, route the antenna toward a rear window

location for best reception. Secure the antenna with double stick tape provided. After securing the antenna with

tape, we advise also securing a section of the antenna cable to a fixed support. This will prevent the antenna from

dropping down in case the double stick tape is exposed to extreme heat, which may loosen its gummed surface.

Route the 3 pin connector toward the control module using caution not to pinch the cable as this will cause poor or

no RF reception to the control module.

1 2 3 4 5 6 7 8 9 10 ... 18 19

Comments to this Manuals

No comments

Audiovox PRO-9056 User Manual Page 5

Comments to this Manuals

Related products and manuals for For the car Audiovox PRO-9056