128-7405B1 of 28Model APS-998Installation ManualThe selectable features can be set manually as explained below, or with the RF feature programmer.To s
128-7405B10 of 28White w/ Black Trace Wire: (+) Siren OutputThis is the positive siren feed wire. Route this wire through a grommet in the firewall t
128-7405B11 of 28Siren Wiring Detail11(-) TO VEHICLE'S CHASSIS GROUNDTO WHITE w/BLACK WIRE OF MODULEPurple Wire: (+) Door Trigger InputIf the veh
128-7405B12 of 28A. Shock Sensor By Pass:If there is a Non Plug in Shock Sensor used with the alarm system and it is not shunted during theRemote Star
128-7405B13 of 2813Entry Illumination DetailGrey w/ Black Trace Wire: Negative Inhibit Input Plus Trigger When ArmedThe Grey w/ Black Trace wire prov
128-7405B14 of 28Brown w/ Black Trace Wire: Positive Inhibit Input Plus Trigger When ArmedThe Brown w/ Black Trace wire provides an instant shutdown
128-7405B15 of 2815Green w/ Orange Trace Wire: Tachometer Input SignalThis wire will continually monitor the engine's tach rate while the unit is
128-7405B16 of 28Channel 3 Relay Wiring Detail16Green w/ Black Trace Wire: 300mA Latched Channel 4 OutputThe Green w/ Black Trace wire supplies a 3
128-7405B17 of 2817NOTE : This is a normally opened starter cut arrangement, when power is removed from thesecurity system, the starter disable featur
128-7405B18 of 2818Black w/ Yellow Trace Wire: Ground Output During Start (Crank)The Black w/ Yellow Trace wire will provide a 300 mA ground output w
128-7405B19 of 28193 Wire Positive Switched Door Locks:In this application, the Red wire of the door lock harness provides a + 12 volt pulse during t
128-7405B2 of 282To program these selectable features;Action System ResponseTurn ignition on No responsePress and release the valet switch 3 times 1
128-7405B20 of 28The Red/Black wire provides a pulse ground output when the unlock button of the transmitter is pressed asecond time after disarming.
128-7405B21 of 2821NOTE: Resistive Circuits, As Well As 4 Wire Polarity Reversal and 5 Wire Alternating 12 VoltDoor Lock Control CircuitsThese applic
128-7405B22 of 2822TEMPERATURE START:When Temperature Start, Bank 3 feature #13 is selected on, the temperature start mode can be activatedfrom the tr
128-7405B23 of 28coils. To achieve optimum performance the coil signals must be evenly distributed. This is accomplishedby first mapping out the firi
128-7405B24 of 28If the unit fails this test, recheck your enable switch connection to the Ground and the Black/White wire ofthe Audiovox Remote Start
128-7405B25 of 28254. Connect the other side of the enable switch to the Black/White enable input wire of the Remote Start unit.The reference diagram
128-7405B26 of 28METHOD 2To connect to the key in sensor circuit as shown for method 2:A. Locate the control wire that connects the drivers door pin s
128-7405B27 of 2827be connected to the hood pin switch. If the hood pin switch is also used for an alarm trigger input, becertain to use the dual dio
128-7405B28 of 2828© 2006 Audiovox Electronics Corp., Hauppauge, NY 11788WWW.audiovox.comFor Customer ServiceVisit Our Website AtProduct Information,
128-7405B3 of 283To exit program mode, turn ignition off, or press and release valet switch.RF Programmable Features Bank 3 Is Remote Start Selectable
128-7405B4 of 284Turn ignition on No responsePress and release the valet switch 3 times 1 Chirp - LED 1 flashWithin 3 seconds, turn ignition Off, On,
128-7405B5 of 28Vehicles Only! The unit provides a selectable ignition control that allows a number of selectable timedoutputs for glow plug pre-heat
128-7405B6 of 28DASH MOUNTED LED:The small LED included in the kit will serve as a visual indicator of the alarm's status and provide a visual
128-7405B7 of 28relay to an existing harness in the chosen location using a cable tie around the relay's wiring harness. CAUTION! Do not wire ti
128-7405B8 of 28IMPORTANT!It is the responsibility of the installing technician to determine the load factor of the vehicles electricalcircuits when t
128-7405B9 of 28GREEN Wire: Ignition 2 OutputConnect this wire to the ignition 2 wire from the ignition switch. This wire will show + 12 volts when
Comments to this Manuals