Audiovox PRO9801 Owner's Manual download pdf (Page 5)

128-8795A

5 of 28

Rev A - Added new URL 11/11

This Remote Start/Alarm System is designed to be used with Automatic Transmission- Fuel Injection

Vehicles Only!

The unit provides a selectable ignition control that allows a number of selectable timed outputs

for glow plug pre-heat in addition to a "Wait To Start Input" either of which may be required for certain diesel

vehicles, (see selectable feature #11 Bank 3 & or Green/Yellow Wire)

. If the diesel engine has a instant fire, (no

glow plug pre-heat system), feature #11 of Bank 3 should remain in the default Gasoline mode setting. For

diesel applications, consult your dealer for the type of ignition system used in your particular vehicle.

Regardless of the vehicle, Gasoline or Diesel, for every installation, the vehicle MUST HAVE a Tach

Signal Input, Automatic Transmission and Fuel Injection.

INSTALLATION OF THE MAJOR COMPONENTS:

CONTROL MODULE:

Select a mounting location inside the passenger compartment (up behind the dashboard). The mounting

location selected must be within 24" of the ignition switch wiring harness to allow connection of the 6 pin

main wiring harness.

Be certain that the chosen location will not interfere with proper operation of the vehicle. Avoid mounting the

module to or routing the wiring around the steering shaft/column, as the module or wiring may wrap around

or block the steering wheel preventing proper control of the vehicle. Secure the module in the chosen

location using cable ties or screws as necessary.

Do Not Mount The Module In The Engine Compartment, as it is not waterproof.

OPTIONAL SIREN:

Select a location in the engine compartment that is not accessible from below the vehicle. The selected

location must be clear of hot or moving parts within the engine compartment. The siren must be pointed

downward to prevent water retention and the flared end must be pointed away from and out of the engine

compartment for maximum sound distribution. Before securing the siren, check behind your chosen loca-

tion to assure that the mounting screws will not penetrate any factory wiring or fluid lines. Secure the siren

mounting bracket using #8 self taping screws or by first using the mounting bracket as a template, scribe

or mark the mounting holes. Drill the marked holes using a 1/8" drill bit, then mount the siren using #8

sheet metal screws.

HOOD AND OPTIONAL TRUNK PIN SWITCHES:

The pin switch included in this package is intended for protecting the hood area of the vehicle. In all cases,

the switch must be mounted to a grounded metal surface. When the pin switch is activated, (hood open),

it will supply a ground to the input wire activating the alarm. In addition, the hood switch is required for the

safety shut down of the remote start unit. If the vehicle is being worked on, this hood switch prevents the

remote start activation even if the RF command to start is issued. This switch must be installeded in all

applications. Failure to do so may result in personal injury or property damage. Mount the switch

in the hood locations away from water drain paths. If necessary, an L bracket may be used to move the

switch away from rain gutters or allow mounting to the firewall behind the hood seal. In both cases, the

switch must be set up to allow the hood to depress the switch at least 1/4 inch when the hood closed, and

fully extended when the hood is opened. For direct mounting, a 1/4 inch hole must be drilled. Carefully

check behind the chosen location to insure the drill will not penetrate any existing factory wiring or fluid

lines.

Drill a 1/4" hole in the desired location and thread the pin switch into it using a 7/16" nut driver or deep well

socket. If using the mounting bracket, first secure the bracket to the desired location and secure the pin

switch in the pre-threaded mounting bracket hole.

For Trunk areas a similar installation method may be used and an optional switch may be purchased from

the Audiovox Accessory Catalog.

1 2 3 4 5 6 7 8 9 10 ... 27 28

Comments to this Manuals

No comments

Audiovox PRO9801 Owner's Manual Page 5

Comments to this Manuals

Related products and manuals for Security access control systems Audiovox PRO9801