Audiovox Pro 9544FT3 User Manual download pdf

SELECTABLE FEATURES

Note: The method of manual override can either be selected to operate from the valet switch or operate

as custom code. Be certain to place a check mark indicating the method used in the box located

on the last page of the owner's manual.

Note: When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver’s

door pin switch in order to begin the passive arming sequence.

RF Programmable Features :

Feature Selection 1 Chirp 2 Chirps 3 Chirps 4 Chirps Default

1st DoorL/UL 1 Sec. 3.5 Sec. 1 Sec L, Dbl. U/L 1 Sec.

2nd Accy Lock Auto Lock On Auto Lock Off Auto Lock Off

3rd Accy. UL Auto UL Dr Auto UL All Auto UL Off Auto UL Off

4th Headlights On Arm On Disarm On Both Off Both

5th Passive Locks Passive Active Active

6th Passive/Active Arm Passive Arm Active Arm Active Arm

7th Voltage Sense Voltage Sense Hardwire Hardwire

8th Siren/Horn Siren/Horn Siren Only Horn Only Siren/Horn

9th Horn Chirp 10mS 16mS 30mS 16mS

10th Override Method Custom Code Valet Valet

11th Chirp Delete From Tx On Off Off

To program these selectable features;

Action System Response

Turn ignition on No response

Press and release the valet switch 3 times 1 Chirp - LED 1 flash

Within 3 seconds, turn ignition Off Short chirp, then long chirp

First Then On 1 chirp = 1 second door locks

Press transmitter Lock button to change 2 chirps = 3.5 second door locks

Press transmitter Lock button to change 3 chirps = 1 sec. lock, dbl 1 sec. unlock

Second Press and release the valet switch 2 chirps = auto locks off

Press transmitter Lock button to change 1 chirp = auto locks on

Third Press and release the valet switch 3 chirps = auto unlock off

Press transmitter Lock button to change 1 chirp = auto unlock drivers door only

Press transmitter Lock button to change 2 chirps = auto unlock all doors

Fourth Press and release the valet switch 3 chirps = headlight output when arming and disarming

Press transmitter Lock button to change 4 chirps = headlight output off

Press transmitter Lock button to change 1 chirp = headlight output when arming

Press transmitter Lock button to change 2 chirps = headlight output when disarming

Model PRO 9544FT3

Installation Manual

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - Model PRO 9544FT3

SELECTABLE FEATURESNote: The method of manual override can either be selected to operate from the valet switch or operateas custom code. Be certain t

Page 2

Page 2Fifth Press and release the valet switch 2 chirps = active locksPress transmitter Lock button to change 1 chirp = passive locksorSixth Press and

Page 3 - WIRING THE SYSTEM

Page 3the dash, located where it can be easily seen from outside the vehicle, yet not be distracting to the driver.Once a location has been selected,

Page 4

Dark Blue Wire: DELAYED 300 mA PULSED OUTPUT / CHANNEL 3The dark blue wire pulses to ground via an independent RF channel from the keychain transmitte

Page 5

Page 5crank positions, and off when the key is in the off position. (This is where the yellow wire from the alarmshould be connected).Cut the low cur

Page 6

Page 62 Pin White Connector: Dash Mounted LEDRoute the red and blue wires in the 2 pin white connector from the LED to the control module, and plug it

Page 7 - COMPLETING THE INSTALLATION

3 Wire Positive Switched 2 Step Door LocksThe green wire provides a positive pulse during arming, or the pulsed + 12 volt lock output. Connect thegree

Page 8

Comments to this Manuals

No comments

Audiovox Pro 9544FT3 User Manual

Browse online or download User Manual for Car alarm Audiovox Pro 9544FT3. Audiovox Pro 9544FT3 User Manual [en]

Summary of Contents

Comments to this Manuals

Related products and manuals for Car alarm Audiovox Pro 9544FT3