Audiovox Rampage ACD88 User Manual Page 12

  • Download
  • Add to my manuals
  • Print
  • Page
    / 20
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 11
1212
1212
12
OPEROPER
OPEROPER
OPER
AA
AA
A
TT
TT
T
ING INSTRUCING INSTRUC
ING INSTRUCING INSTRUC
ING INSTRUC
TT
TT
T
IONS / SETIONS / SET
IONS / SETIONS / SET
IONS / SET
TT
TT
T
ING THE CLOCK / CD ERRING THE CLOCK / CD ERR
ING THE CLOCK / CD ERRING THE CLOCK / CD ERR
ING THE CLOCK / CD ERR
OR CODESOR CODES
OR CODESOR CODES
OR CODES
1. Switch the vehicle ignition and radio “on”.
2. Press the Time/Frequency (T/F) button to call the time display.
3. Within 10 seconds, press and hold the T/F button until a single beep sounds and the
time display flashes.
4. With the display flashing, press the Up MANU/SKIP ( ) button to adjust the hours
and A/P indication, or the Down MANU/SKIP ( ) button to adjust the minutes to
the correct time.
5. Five seconds after the last hour or minute adjustment is made, the time will be set in
the unit and the display will return to the normal indication.
SETSET
SETSET
SET
TT
TT
T
ING THE CLOCKING THE CLOCK
ING THE CLOCKING THE CLOCK
ING THE CLOCK
CD PLCD PL
CD PLCD PL
CD PL
AA
AA
A
YER ERRYER ERR
YER ERRYER ERR
YER ERR
OR CODESOR CODES
OR CODESOR CODES
OR CODES
If a problem should develop while operating the CD player, an error code (ER-1, ER-2,
ER-3, etc.) may appear on the display panel. This can indicate a number of problems
with the unit, including a mechanical error or an error in the microprocessor control of the
player. If an error code should appear, try ejecting and re-loading the disc into the player.
While the disc is out of the unit, make sure it is clean, undamaged, and loaded correctly
(label surface up). You may also try activating the RESET button dm on the unit, but this
will also erase the time and pre-set memories.
If the suggested measures do not solve the problem, contact an approved warranty
station near you for further assistance.
3.To restore the front panel to its normal
operating position, press the release
button in the upper right corner of the
blank panel; the panel will then flip down
to expose the operating controls in the
horizontal position. Simply push in on
the bottom edge of this side to engage
the panel in its normal vertical position.
MODE
BND
SEL
MONO
LOC
EQ
T/F
EJECT
OPEN
LOUD
M
A
N
U
/
S
K
I
P
CD-R/RW PLAYBACK
SCNMUTE
RPT
3
SCN
2
SHF
45
D.DN D.UP
61
PAUAS/PS
POWER
ACD-88
AF TA TP PTY
MP3 EQ
CDP EON
LOC REG
ST MONO
LOUD
D.DIR
SW
ROCK
CLAS
POP
RELEASE BUTTON
(BLANK SURFACE)
CD EJECT BUTTON
FRONT PANEL IN
NORMAL POSITION
CD EJECT
BUTTON
(REF)
FRONT PANEL IN
REVERSE POSITION
DISC SLOT
PANEL IN FOLD-DOWN POSITION
FRONT PANEL
RELEASE (OPEN)
BUTTON
Page view 11
1 2 ... 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Comments to this Manuals

No comments