Audiovox Platinum APS 675 User Manual download pdf (Page 3)

allowed for the body of the switch, and also that the drill will not penetrate any existing factory wiring or fluid lines.

Drill a 1/4" hole in the desired location and mount the switch by passing it through the panel from the

underside. Secure the switch using the nut, star washer, and on/off face plate. It is suggested that the

switch be oriented to allow the on position to be up toward the driver and the off position to be down or away

from the driver. Route the switch wires toward the control module. Place the RED rubber boot, included in

the kit, over the switch handle to differentiate this switch from the program switch.

The APS-675 is to be used in vehicles with AUTOMATIC TRANSMISSIONS only! Although this combination

Keyless Entry/Remote Start unit is a sophisticated system with many advanced features, IT MUST NOT be

installed into a vehicle with a manually operated transmission. Doing so may result in serious personal injury

and property damage.

IMPORTANT!

DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MULTI PIN INPUT / OUTPUT HARNESS

INTO THE CONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HAVE BEEN MADE. AFTER

SELECTING YOUR TARGET WIRES AS DEFINED BELOW, DISCONNECT THE NEGATIVE BATTERY

CABLE FROM THE VEHICLE BATTERY PRIOR TO MAKING ANY CONNECTIONS.

WIRING THE 6 PIN MAIN POWER HARNESS:

RED w/ WHITE Trace Wire: + 12 volt Battery 1 Source

Connect this wire toa+12VDCconstant source found at the vehicle's ignition switch using the 30 Amp fuse

and holder provided. This wire provides power for the control circuit as well as the ignition 1 and ignition 2 relays.

RED Wire: + 12 Volt Battery 2 Source

Connect this wire toa+12VDCconstant source found at the vehicle's ignition switch using the 30 Amp fuse

and holder provided, but NOT the same vehicle wire as used by the battery 1 source. Most vehicles have

more than one battery source supplying power to the ignition switch. Separate feed wires must be used for

the Red and Red/White wires. If your vehicle does not have two battery feed wires at the ignition switch then

it is possible to connect both wires to the vehicle's battery. This wire provides power for the start relay and

the accessory relay.

IMPORTANT!

It is the responsibility of the installing technician to determine the load factor of the vehicles electrical circuits

when the vehicle is running and to adequately fuse the two power wires based on that load. If the vehicle,

running under load with the air conditioner, heater blower motor, and accessories exceeds 24 Amps continuous,

we recommend that two fuses be used in combination on each power wire as shown below. For additional

information see Tech Update issued 9/30/96.

YELLOW Wire: Starter Output

Careful consideration for the connection of this wire must be made to prevent the vehicle from

starting while in gear. Understanding the difference between a mechanical and an electrical

Neutral Start Switch will allow you to properly identify the circuit and select the correct installation

method. In addition you will realize why the connection of the safety wire is required for all

mechanical switch configurations.

Failure to make this connection properly can result in personal injury and property damage.

In all installations it is the responsibility of the installing technician to test the remote start unit and assure

that the vehicle cannot start via RF control in any gear selection other than park or neutral.

In both mechanical and electrical neutral start switch configurations, the connection of the Yellow wire will be

made to the low current start solenoid wire of the ignition switch harness. This wire will have +12 volts when

the ignition switch is turned to the start (crank) position only. This wire will have 0 volts in all other ignition

switch positions.

NOTE: This wire must be connected to the vehicle side of the starter cut relay (when used). For the electrical

neutral switch configuration, this connection must be made between the starter inhibit relay, ( when

1 2 3 4 5 6 7 8 ... 17 18

Comments to this Manuals

No comments

Audiovox Platinum APS 675 User Manual Page 3

Comments to this Manuals

Related products and manuals for For the car Audiovox Platinum APS 675