128-8795A1 of 281Rev A - Added new URL 11/11Model PRO9801CInstallation ManualSELECTABLE FEATURESThe selectable features can be set manually as explain
128-8795A10 of 2810Rev A - Added new URL 11/11White w/ Black Trace Wire: (+) Siren OutputThis is the positive siren feed wire. Route this wire through
128-8795A11 of 2811Rev A - Added new URL 11/11Optional Siren Wiring Detail(-) TO VEHICLE'S CHASSIS GROUNDTO WHITE w/BLACK WIRE OF MODULEPurple Wi
128-8795A12 of 2812Rev A - Added new URL 11/11The Light Blue wire can be used to accommodate the following situations:A. Shock Sensor By Pass:If there
128-8795A13 of 2813Rev A - Added new URL 11/11Entry Illumination DetailGrey w/ Black Trace Wire: Negative Inhibit Input Plus Trigger When ArmedThe Gr
128-8795A14 of 2814Rev A - Added new URL 11/11Brown w/ Black Trace Wire: Positive Inhibit Input Plus Trigger When ArmedThe Brown w/ Black Trace wire
128-8795A15 of 2815Rev A - Added new URL 11/11Brown Wire: Negative Door TriggerIf the vehicle's door courtesy light switches ground when the doo
128-8795A16 of 2816Rev A - Added new URL 11/11Channel 3 Relay Wiring DetailGreen w/ Black Trace Wire: 300mA Latched Channel 4 OutputThe Green w/ Bla
128-8795A17 of 2817Rev A - Added new URL 11/11Note : This is a normally opened starter cut arrangement, when power is removed from thesecurity system,
128-8795A18 of 2818Rev A - Added new URL 11/11Black w/ Yellow Trace Wire: Ground Output During Start (Crank)The Black w/ Yellow Trace wire will provid
128-8795A19 of 2819Rev A - Added new URL 11/113 Wire Positive Switched Door Locks:In this application, the Red wire of the door lock harness provides
128-8795A2 of 282Rev A - Added new URL 11/11To program these selectable features;Action System ResponseTurn ignition on No responsePress and release t
128-8795A20 of 2820Rev A - Added new URL 11/11The Red/Black wire provides a pulse ground output when the unlock button of the transmitter is pressed a
128-8795A21 of 2821Rev A - Added new URL 11/11Note: Resistive Circuits, As Well As 4 Wire Polarity Reversal and 5 Wire Alternating 12 VoltDoor Lock Co
128-8795A22 of 2822Rev A - Added new URL 11/11TEMPERATURE START:When Temperature Start, Bank 3 feature #13 is selected on, the temperature start mode
128-8795A23 of 2823Rev A - Added new URL 11/11To use the adaptor, the Green/Black wires must connect to the negative side of the ignition coil(s).1. F
128-8795A24 of 2824Rev A - Added new URL 11/11To Exit Remote Start Override Mode:1. With the system disarmed, Press and Hold the pushbutton switch loc
128-8795A25 of 2825Rev A - Added new URL 11/11KEY IN SENSOR CIRCUITS:If the vehicle you are working on does not have or you cannot locate the ECM refe
128-8795A26 of 2826Rev A - Added new URL 11/11METHOD 2To connect to the key in sensor circuit as shown for method 2:A. Locate the control wire that co
128-8795A27 of 2827Rev A - Added new URL 11/11COMPLETING THE INSTALLATION:After you have confirmed the operation of the Audiovox Remote Start unit and
128-8795A28 of 2828Rev A - Added new URL 11/11© 2011 Audiovox Electronics Corp., Hauppauge, NY 11788128-8795AFor technical support go to www.pursuitca
128-8795A3 of 283Rev A - Added new URL 11/11To exit program mode, turn ignition off, or press and release valet switch.RF Programmable Features Bank 3
128-8795A4 of 284Rev A - Added new URL 11/11Action System ResponseTurn ignition on No responsePress and release the valet switch 3 times 1 Chirp - LED
128-8795A5 of 285Rev A - Added new URL 11/11This Remote Start/Alarm System is designed to be used with Automatic Transmission- Fuel InjectionVehicles
128-8795A6 of 286Rev A - Added new URL 11/11THE PUSH-BUTTON/LED/RECEIVER/ANTENNA ASSEMBLY:The Superheterodyne Receiver Antenna Assembly provided with
128-8795A7 of 287Rev A - Added new URL 11/11WIRING THE 6 PIN MAIN POWER HARNESS:Note: Do not remove the fuse holders from this wire harness. Fuses mus
128-8795A8 of 288Rev A - Added new URL 11/11YELLOW Wire: Starter OutputCareful consideration for the connection of this wire must be made to prevent
128-8795A9 of 289Rev A - Added new URL 11/11GREEN Wire: Ignition 2 OutputConnect this wire to the ignition 2 wire from the ignition switch. This wire
Comments to this Manuals