Audiovox PRO9801 Owner's Manual download pdf (Page 4)

128-8795A

4 of 28

Rev A - Added new URL 11/11

Action System Response

Turn ignition on No response

Press and release the valet switch 3 times 1 Chirp - LED 1 flash

Within 3 seconds, turn ignition Off, On, Off, On Short chirp, then 2 long chirps

This Action Accesses Feature Bank 3 Remote Start Selectable Features

First Press the valet switch one time 1 chirp = defrost output pulsed

Press transmitter Lock button to change 2 chirps = defrost output 10 Mins

Second Press and release the valet switch 2 chirps = RF start chirp on

Press transmitter Lock button to change 1 chirp = RF start chirp off

Third Press and release the valet switch 2 chirps = run time set for 10 mins

Press transmitter Lock button to change 3 chirps = run time set fro 15 mins

Press transmitter Lock button to change 4 chirps = run time set for 20 mins

Press transmitter Lock button to change 5 chirps = run time set for 45 mins

Press transmitter Lock button to change 6 chirps = run time set for 60 mins

Press transmitter Lock button to change 1 chirp = run time set for 5 mins

Fourth Press and release the valet switch 1 chirp = parking lights on steady w/RS active

Press transmitter Lock button to change 2 chirps = parking lights flashing w/RS active

Fifth Press and release the valet switch 2 chirps = tachometer input checking

Press transmitter Lock nutton to change 3 chirps = DBI Tach Mode

Press transmitter Lock button to change 4 chirps = Hybrid Mode

Press transmitter Lock button to change 1 chirp = voltage sense input checking

Sixth Press and release the valet switch 1 chirp = greater than 0.5 V check before start

Press transmitter Lock button to change 2 chirps = less than 0.5 V check before start

Seventh Press and release the valet switch 2 chirps = ign 2 on during crank

Press transmitter Lock button to change 3 chirps = ign 2 same as accessory

Press transmitter Lock button to change 1 chirp = ign 2 off during crank

Eighth Press and release the valet switch 2 chirps = ign 3 on during crank

Press transmitter Lock button to change 3 chirps = ign 3 same as accessory

Press transmitter Lock button to change 4 chirps = ign 3 same as starter

Press transmitter Lock button to change 1 chirp = ign 3 off during crank

Ninth Press and release the valet switch 1 chirp = diagnostics off

Press transmitter Lock button to change 2 chirps = diagnostics on

Tenth Press and release the valet switch 2 chirps = crank time 1.0 sec

Press transmitter Lock button to change 3 chirps = crank time 1.5 sec

Press transmitter Lock button to change 4 chirps = crank time 2.0 sec

Press transmitter Lock button to change 1 chirp = crank time 0.8 sec

Eleventh Press and release the valet switch 1 chirp = unit set for gasoline engine

Press transmitter Lock button to change 2 chirps = unit set for diesel engine 10 sec delay

Press transmitter Lock button to change 3 chirps = unit set for diesel engine 15 sec delay

Press transmitter Lock button to change 4 chirps = unit set for diesel engine 20 sec delay

Twelfth Press and release the valet switch 1 chirp = transponder output while R/S active

Press transmitter Lock button to change 2 chirps = transponder output during start only

Press transmitter Lock button to change 3 chirps = transponder output until ignition turned off

Thirteenth Press and release the valet switch 1 chirp = temperature start off

Press transmitter Lock button to change 2 chirps = temperature start on

Fourteenth Press and release the valet switch 1 chirp = crank averaging w/voltage input checking

Press transmitter Lock button to change 2 chirps = preset crank time w/voltage input check

Fifteenth Press and release the valet switch 1 chirp = shk sensor shuntnted until clear

Press transmitter Lock button to change 2 chirps = shk sensor shunted for the R/S cycle

Press transmitter Lock button to change 3 chirps = shk sensor shunted from 1 tx start cycle

Sixteenth Press and release the valet switch 1 chirp = turbo timer off

Press transmitter Lock button to change 2 chirps = turbo timer 3 mins

Press transmitter Lock button to change 3 chirps = turbo timer 5 mins

Press transmitter Lock button to change 4 chirps = turbo timer 10 mins

Seventeenth Press and release the valet switch 1 chirp = aux o/p Black/Blue single pulse

Press transmitter Lock button to change 2 chirps = aux o/p Black/Blue as alarm feature #1

Eighteenth Press and release the valet switch 1 chirp = double press to start

Press transmitter Lock button to change 2 chirps = single press to start

Turn the ignition off to: Exit Programming Mode

Note: Once you enter the feature programming mode, do not allow more than 15 seconds to pass between steps or the

programming will be terminated.

1 2 3 4 5 6 7 8 9 ... 27 28

Comments to this Manuals

No comments

Audiovox PRO9801 Owner's Manual Page 4

Comments to this Manuals

Related products and manuals for Security access control systems Audiovox PRO9801