Audiovox D2016 - DVD Player - 10.2 Operations Instructions Page 74
- Page / 117
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
74
10
Controlling the rest of your system
4 Repeat steps 2 through 3 for the other components you want to control.
To try out the remote control, switch the component on or off (into standby) by pressing u SOURCE. If it doesn’t
seem to work, select the next code from the list (if there is one).
5 Press RCU SETUP to exit the preset setup mode.
Programming signals from other remote controls
If the preset code for your component is not available, or the available preset codes do not operate correctly, you
can program signals from the remote control of another component. This can also be used to program additional
operations (buttons not covered in the presets) after assigning a preset code.
The remote can store about 120 preset codes from other components (this has been tested with codes of Pioneer
format only).
Certain buttons represent operations that cannot be learned from other remote controls. The buttons available
are shown below:
RECEIVER
D.ACCESS
CH LEVEL
DIMMER SLEEP
SIGNAL SEL
SPEAKERS
MPX
PRESET TUNE
BAND PTY
ZONE 2 ZONE 3
HD ZONE
CLASS
FEATURES
+Favorite
Z2 Z3 HDZ
HDMI OUT
MCACC
AUTO/ALC/
DIRECT
AUTO
S.RTRV
STANDARD ADV SURR
OPTION
P. CTRL
+
PHASE
ECO
PQLS
ENTER
/
CLR
CH
CH
22
546
8
0
79
132
AUDIO
DISP
iPod CTRL
HOME
MENU
INPUT
SELECT
iPod
USB CBL
STATUS
SATTUNERMHL
ADPT
CDTV
RCU SETUP
STANDBY/ON
BDR
BD DVDDVR
NET
HDMI
RECEIVER
MUTE
VOLUME
TOP MENU
VIDEO
PARAMETER
AUDIO
PARAMETER
RETURN
TOOLS
MENU
ALL ZONE STBY
DISCRETE ON
CH
TV CONTROL
INPUT
VOL
ENTER
SOURCE
1 Press and hold RCU SETUP, then press ‘2’ for three seconds.
Release the button after the LED flashes once. The LED continues to flash.
! To “learn” codes at the TV CONTROL buttons, proceed to step 3.
! To cancel the preset setup mode press RCU SETUP.
2 Press the input function button for the component you want to control.
The LED blinks once and flashes continuously.
3 Point the two remote controls towards each other, then press the button that will be
doing the learning on this receiver’s remote control.
The LED flashes once, then stops flashing, remaining lit.
! The remote controls should be 3 cm (1 inch) apart.
3 cm
(1 inch)
This receiver’s
remote control
Other remote
control
4 Press the corresponding button on the other remote control that is sending (teaching) the
signal to this receiver’s remote control.
If the LED lights for one second and continues to flash, the setting has been successfully completed.
! If the LED flashes for five seconds, it means the memory is full. See Erasing all learnt settings that are in one
input function on page 75 to erase a programmed button you’re not using to free up more memory (note that
some signals may take more memory than others).
! Note that interference from TVs or other devices will sometimes result in the remote control learning the
wrong signal.
! Some commands from other remote controls cannot be learned, but in most cases the remotes just need to
be moved closer together or farther apart.
5 To program additional signals for the current component repeat steps 3 and 4.
To program signals for another component, exit and repeat steps 2 through 4.
6 Press RCU SETUP to exit the programming mode.
Erasing one of the remote control button settings
This erases one of the buttons you have programmed and restores the button to the factory default.
1 Press and hold RCU SETUP, then press ‘7’ for three seconds.
Release the button after the LED flashes once. The LED continues to flash.
! To erase operations registered at the TV CONTROL buttons, proceed to step 3.
! To cancel the preset setup mode press RCU SETUP.
2 Press the input function button corresponding to the command to be erased.
The LED flashes once.
3 Press and hold the button to be erased for three seconds.
If the LED lights for one second, the erasing has been successfully completed.
4 Repeat step 3 to erase other buttons.
5 Press RCU SETUP to exit the erasing mode.
- SC-1223-K 1
- IMPORTANT 2
- ESTABLISH A SAFE LEVEL: 3
- GUIDELINES: 3
- Contents 4
- 11 The Advanced MCACC menu 5
- 14 Additional information 5
- Important 6
- Checking what’s in the box 8
- Our philosophy 8
- Features 8
- Installing the receiver 9
- Loading the batteries 9
- Before you start 10
- Using AVNavigator for Mac 11
- Controls and displays 12
- Front panel 16
- Connecting your equipment 18
- Rear panel 19
- Placing the speakers 21
- Connecting the speakers 22
- Selecting the Speaker system 24
- About the audio connection 24
- About the video converter 25
- Connecting using HDMI 26
- Connecting external antennas 31
- Making MULTI-ZONE connections 32
- Connecting an iPod 34
- Connecting a USB device 35
- Connecting to a wireless LAN 35
- Connecting an IR receiver 36
- Plugging in the receiver 36
- Basic Setup 37
- The Input Setup menu 39
- Operation Mode Setup 40
- About the Home Menu 41
- Basic playback 42
- Playing a source 43
- Playing an iPod 44
- Playing a USB device 45
- About playable file formats 46
- Listening to the radio 47
- Listening to your system 50
- Front left 52
- speaker 52
- Front right 52
- speaker 52
- Selecting MCACC presets 53
- Choosing the input signal 53
- Introduction 55
- About HTC Connect 56
- Basic playback controls 56
- About network playback 58
- Music files 59
- Control with HDMI function 60
- HDMI Setup 61
- Before using synchronization 62
- About synchronized operations 62
- Setting the PQLS function 62
- Using other functions 64
- Audio parameter menu 65
- Video parameter menu 67
- Using the MULTI-ZONE controls 69
- Using the sleep timer 70
- Dimming the display 70
- Switching the HDMI output 70
- Checking your system settings 70
- Default system settings 71
- About the Remote Setup menu 73
- Operating multiple receivers 73
- RECEIVER 74
- Direct function 75
- (Discrete On) functions 75
- TV and Audio/Video components 76
- Button(s) TV (Projector) 77
- The Advanced MCACC menu 78
- Automatic MCACC (Expert) 79
- Manual MCACC setup 80
- Checking MCACC Data 83
- Data Management 83
- Manual speaker setup 86
- Room size (ft 87
- Network Setup menu 88
- MHL Setup 89
- The Other Setup menu 89
- Auto Power Down 90
- Volume Setup 90
- Remote Control Mode Setup 90
- Software Update 90
- ZONE Setup 91
- On Screen Display Setup 91
- Play ZONE Setup 91
- Troubleshooting 95
- No sound 95
- Other audio problems 96
- ADAPTER PORT terminal 97
- Settings 97
- Remote control 98
- AVNavigator 99
- USB interface 100
- Symptoms Causes Remedies 101
- Web Control 102
- Wireless LAN 102
- Additional information 103
- HTC Connect 104
- Surround sound formats 104
- About HDMI 104
- About iPod 105
- Windows 7 105
- Software license notice 105
- Speaker Setting Guide 106
- Cleaning the unit 108
- Glossary 109
- Features index 112
- Specifications 113
- Preset code list 114
- In the USA/Aux Etats-Unis 117
- In Canada/Aux Canada 117
Related products and manuals for AV receivers Audiovox D2016 - DVD Player - 10.2
AV receivers Audiovox PEQ-200 Owner's Manual
(100 pages)
(100 pages)
AV receivers Audiovox ADC700 Owner's Manual
(73 pages)
(73 pages)
© 2020, manymanuals.com. All rights reserved. | 2.287 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals