Audiovox D2016 - DVD Player - 10.2 Operations Instructions download pdf (Page 98)

FAQ

Symptom Remedy

The various system settings are not

stored.

Do not pull out the power cord while conducting the settings. (The settings will be stored

when both the main zone and sub zone turn off. Turn off all zones before pulling out the

power cord.)

Certain listening modes or

HOME MENU items cannot be

selected.

When Operation Mode is set to Basic, the Pioneer-recommended settings are made and

not all of the functions can be used. To use all of the functions without restrictions, set

Operation Mode to Expert (see Operation Mode Setup on page 40).

Professional Calibration EQ graphical output

Symptom Remedy

The reverb characteristics graph

after EQ calibration does not appear

entirely flat.

There are cases where the graph does not appear flat (even when selecting ALL CH ADJ

in the Auto MCACC Setup) due to adjustments made to compensate for room character-

istics to achieve optimal sound.

Areas of the graph may appear identical (before and after) when there is little or no

adjustment needed.

The graph may appear to have shifted vertically when comparing before and after mea-

surements.

EQ adjustments made using the

Manual MCACC setup do not appear

to change the reverb characteristics

graph after EQ calibration.

Despite level adjustments being made, the filters used for analysis may not display these

adjustments in the reverb characteristics graph after EQ calibration. However, these

adjustments are taken into account by the filters dedicated to overall system calibration.

Lower frequency response curves do

not seem to have been calibrated for

SMALL speakers.

Low frequencies used in bass management (the subwoofer channel) will not change for

speakers that have been specified as SMALL in the configuration, or do not output these

frequencies.

Calibration is performed, but due to your speakers’ low frequency limitations, no measur-

able sound is output for display.

Display

Symptom Remedy

The display is dark or off. Press DIMMER repeatedly to select a different brightness.

The OSD screen is not displayed. The on-screen display is not displayed unless the receiver’s HDMI OUT 1 terminal and

the TV are connected with an HDMI cable. If the TV does not support HDMI, perform the

operations and make the settings watching the display on the receiver’s front panel.

Depending on the type of video input signal (4K, 3D, etc.), the on-screen display may not

be displayed.

You can’t get DIGITAL to display

when using SIGNAL SEL.

Check the digital connections and make sure that the digital inputs are assigned cor-

rectly (see The Input Setup menu on page 39).

2 DIGITAL or DTS does not light

when playing Dolby/DTS software.

These indicators do not light if playback is paused.

Check the playback (especially the digital output) settings of the source component.

Symptom Remedy

When playing Dolby Digital or DTS

sources, the receiver’s format indica-

tors do not light.

Check that the player is connected using a digital connection.

Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on

page 53).

Check that the player isn’t set up so that Dolby Digital and DTS sources are converted to

PCM.

Ensure that if there are several audio tracks on the disc, the Dolby Digital or DTS is

selected.

When playing certain discs, none of

the receiver’s format indicators light.

The disc may not contain 5.1/6.1 channel material. Check the disc packaging for more on

what audio tracks are recorded on the disc.

When playing a disc with the listen-

ing mode set to Auto Surround or

ALC, 2 Pro Logic II or DTS Neo:X

appear on the receiver.

Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on

page 53).

If a two channel soundtrack is currently playing (including Dolby Surround encoded),

then this is not a malfunction. Check the disc packaging for details about the audio

tracks available.

During playback of DVD-Audio, the

display shows PCM.

This will occur when playing DVD-Audio material over the HDMI connection. This is not a

malfunction.

The power turns off automatically

and some indicator flashes, or some

indicator flashes and the power does

not turn on.

See the Power section (page 95).

Remote control

Symptom Remedy

Cannot be remote controlled.

Press

on the remote control to switch to the receiver control mode.

Set the remote control unit’s remote control mode so that it matches the setting on the

main unit (see Operating multiple receivers on page 73).

Check whether the receiver’s remote control mode is properly set (see Remote Control

Mode Setup on page 90).

Try replacing the batteries in the remote control (see Loading the batteries on page 9).

Be sure to operate within 7 m (23 ft.) and a 30º angle of the remote sensor on the front

panel (see Operating range of remote control unit on page 9).

Check that there are no obstacles between the receiver and the remote control.

Make sure that there is no fluorescent or other strong light shining on to the remote

sensor.

Other components can’t be operated

with the system remote.

If the battery ran down, the preset codes may have been cleared. Re-enter the preset

codes.

The preset code may be incorrect. Redo the procedure for entering preset codes.

When commands from the remote control units of other devices are registered using the

learning function, in some cases they may not be learned properly. In this case, register

the commands again using the learning function (see page 74). If they still do not work,

they may be in a special format that cannot be registered on this receiver’s remote con-

trol. Operate the device using another remote control.

1 2 ... 93 94 95 96 97 98 99 100 101 102 103 ... 116 117

Comments to this Manuals

No comments

Audiovox D2016 - DVD Player - 10.2 Operations Instructions Page 98

Comments to this Manuals

Related products and manuals for AV receivers Audiovox D2016 - DVD Player - 10.2