Audiovox D2016 - DVD Player - 10.2 Operations Instructions download pdf (Page 80)

The Advanced MCACC menu

3 Connect the microphone to the MCACC SETUP MIC jack on the front panel.

Make sure there are no obstacles between the speakers and the microphone.

PHONES

SPEAKERS

MULTI-ZONE

CONTROL

ZONE 2

ON/OFF

HDZONE

ON/OFF

PHASE

CONTROL

MCACC

SETUP MIC

HDMI 5 INPUT/

MHL (

5V 0.9

)

AUTO/ALC/

DIRECTECO BAND TUNER EDIT

iPod iPhone iPad

DIRECT CONTROL

with USB

5V 2.1

Microphone

Tripod

If you have a tripod, use it to place the microphone so that it’s about ear level at your normal listening position. If

you do not have a tripod, use some other object to install the microphone.

! It may not be possible to measure correctly if the microphone is placed on a table, sofa, etc.

4 When you’re finished setting the options, select START then press ENTER.

5 Follow the instructions on-screen.

6 Wait for the Auto MCACC Setup to finish outputting test tones.

A progress report is displayed on-screen while the receiver outputs test tones to determine the speakers present

in your setup. Try to be as quiet as possible while it’s doing this.

! With error messages (such as Too much ambient noise! or Check microphone.), select RETRY after check-

ing for ambient noise (see Problems when using the Auto MCACC Setup on page 39) and verifying the mic

connection. If there doesn’t seem to be a problem, you can simply select GO NEXT and continue.

! Do not adjust the volume during the test tones. This may result in incorrect speaker settings.

7 If necessary, confirm the speaker configuration in the GUI screen.

The configuration shown on-screen should reflect the actual speakers you have.

If no operations are performed for 10 seconds while the speaker configuration check screen is being displayed,

the Auto MCACC Setup will resume automatically. In this case, you don’t need to select ‘OK’ and press ENTER in

step 8.

! If you see an ERR message (or the speaker configuration displayed isn’t correct), there may be a problem

with the speaker connection. If selecting RETRY doesn’t work, turn off the power and check the speaker con-

nections. If there doesn’t seem to be a problem, you can simply use i/j to select the speaker and k/l to

change the setting and continue.

! If the speaker is not pointed to the microphone (listening position) or when using speakers that affect the

phase (dipole speakers, reflective speakers, etc.), Reverse Phase may be displayed even if the speakers are

properly connected.

If Reverse Phase is displayed, the speaker’s wiring (+ and –) may be inverted. Check the speaker

connections.

— If the connections were wrong, turn off the power, disconnect the power cord, then reconnect properly.

After this, perform the Auto MCACC procedure again.

— If the connections were right, select GO NEXT and continue.

8 Make sure ‘OK’ is selected, then press ENTER.

A progress report is displayed on-screen while the receiver outputs more test tones to determine the optimum

receiver settings.

Again, try to be as quiet as possible while this is happening. It may take 3 to 7 minutes.

! If you selected a STAND.WAVE Multi-Point setup (in step 2), you will be asked to place the mic at the 2nd

and 3rd reference points before finally placing it at your main listening position.

9 The Auto MCACC Setup procedure is completed and the Advanced MCACC menu reappears

automatically.

The settings made in the Auto MCACC Setup should give you excellent surround sound from your system, but

it is also possible to adjust these settings manually using the Manual MCACC setup menu (starting below) or

Manual SP Setup menu (starting on page 86).

! Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12

cm (5 inches) will end up with different size settings. You can correct the setting manually using the Manual

speaker setup on page 86.

! The subwoofer distance setting may be farther than the actual distance from the listening position. This set-

ting should be accurate (taking delay and room characteristics into account) and generally does not need to

be changed.

! If Auto MCACC Setup measurement results are incorrect due to the interaction of the speakers and viewing

environment, we recommend adjusting the settings manually.

You can also choose to view the settings by selecting individual parameters from the MCACC Data Check screen

(see Checking MCACC Data on page 83).

Press RETURN after you have finished checking each screen. When you’re finished, select RETURN to go back to

the Home Menu.

Be sure to disconnect the microphone from this receiver upon completion of the Auto MCACC Setup.

Manual MCACC setup

You can use the settings in the Manual MCACC setup menu to make detailed adjustments when you’re more

familiar with the system. Before making these settings, you should have already completed Automatically con-

ducting optimum sound tuning (Full Auto MCACC) on page 38.

You only need to make these settings once (unless you change the placement of your current speaker system or

add new speakers).

CAUTION

! The test tones used in the Manual MCACC setup are output at high volume.

Important

! Press the MCACC button while the pertinent setup screens are displayed to select MCACC presets.

! For some of the settings below, you’ll have to connect the setup microphone to the front panel and place it

about ear level at your normal listening position. Press HOME MENU to display the Home Menu before you

connect the microphone to this receiver.

! See Problems when using the Auto MCACC Setup on page 39 for notes regarding high background noise

levels and other possible interference.

! If you’re using a subwoofer, switch it on and turn up the volume to the middle position.

1 Select ‘Manual MCACC’ from the Advanced MCACC menu.

See Making receiver settings from the Advanced MCACC menu on page 79 if you’re not already at this screen.

1 2 ... 75 76 77 78 79 80 81 82 83 84 85 ... 116 117

Comments to this Manuals

No comments

Audiovox D2016 - DVD Player - 10.2 Operations Instructions Page 80

Comments to this Manuals

Related products and manuals for AV receivers Audiovox D2016 - DVD Player - 10.2