Audiovox D2016 - DVD Player - 10.2 Instruction Manual download pdf (Page 17)

Connecting Your Speakers

—Continued

Before you connect your speakers, read the following:

• Disconnect the power cord from the wall outlet.

• Read the instructions supplied with your speakers.

•Pay close attention to speaker wiring polarity. In other

words, connect positive (+) terminals only to positive

(+) terminals, and negative (–) terminals only to nega-

tive (–) terminals. If you get them the wrong way

around, the sound will be out of phase and will sound

odd.

• Only use speakers with an impedance of between 6

and 16 ohms. If you use speakers with a lower imped-

ance, and use the ampliﬁer at high volume levels for a

long period of time, the built-in protection circuit may

be activated.

• Unnecessarily long or very thin speaker cables may

affect the sound quality and should be avoided.

• Be careful not to short the posi-

tive and negative connections.

Doing so may damage the AV

Receiver.

• Don’t connect more than one

cable to each speaker terminal.

Doing so may damage the AV

Receiver.

• If you want to connect a single speaker instead of a

pair, connect it to either the left or right speaker termi-

nals, not both.

Attaching the Speaker Labels

The AV Receiver’s positive (+) speaker terminals are

color-coded for ease of identiﬁcation. (The negative (–)

speaker terminals are all black.)

The supplied speaker labels are also color-coded and you

should attach them to the positive (+) side of each

speaker cable in accordance with the above table. All you

need to do then is to match the color of each label to the

corresponding speaker terminal.

Connecting the Speaker Cables

The following illustration shows which speakers should be connected to which terminals.

Connecting Your Speakers

Speaker terminal Color

Front left White

Front right Red

Center Green

Surround left Blue

Surround right Gray

Surround back Brown

Strip 5/8" (15 mm) of

insulation from the

ends of the speaker

cables, and twist the

bare wires tightly, as

shown.

Unscrew the terminal. Fully insert the bare

wires. Screw the terminal tight.

5/8" (15 mm)

AC OUTLET

AC 120

V 60

SWITCHED

120

W 1

MAX.

FRONT

SPEAKERS A

SURROUND

SPEAKERS

CENTER

SPEAKER

SURROUND BACK

SPEAKER

FRONT

SPEAKERS B

ANTENNA

OPTICAL COAXIAL

123

DIGITAL

REMOTE

CONTROL

IN IN

FRONT

SURR

CENTER

SUB

WOOFER

OUT

VIDEO 2

VIDEO 1

DVD MONITOR

OUT

VIDEO

S VIDEO

DVD

TAPE

VIDEO 2

VIDEO 1

SUBWOOFER

PRE OUT

VIDEO 1

/2/3IN

DVD

COMPONENT VIDEO

OUT

Class 2 Wiring

FRONT

SPEAKERS A

SURROUND

SPEAKERS

CENTER

SPEAKER

SURROUND BACK

SPEAKER

FRONT

SPEAKERS B

LINE INPUT

LINE

INPUT

Surround

left

speaker

Surround

right

speaker

Front

left

speaker

Front

right

speaker

Front

left

speaker

Front

right

speaker

Center

speaker

Surround

back

speaker

Speaker set B

Speaker set A

SUBWOOFER

PRE OUT

Powered

subwoofer

The SUBWOOFER PRE OUT should be connected to the

input on your powered subwoofer. If your subwoofer

doesn’t have an amp built-in, you’ll need to use an

external amp. See the manual supplied with your

subwoofer for more information.

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 59 60

Comments to this Manuals

No comments

Audiovox D2016 - DVD Player - 10.2 Instruction Manual Page 17

Comments to this Manuals

Related products and manuals for AV receivers Audiovox D2016 - DVD Player - 10.2