Audiovox D2016 - DVD Player - 10.2 Instruction Manual download pdf (Page 39)

Common Functions

—Continued

With this function you can temporarily mute the output

of the TX-SR502/TX-SR502E.

To unmute the TX-SR502/TX-SR502E,

press the

remote controller’s [MUTING] button again, or adjust

the volume. The output is unmuted and the MUTING

indicator goes off.

Muting is cancelled when the TX-SR502/TX-SR502E is

set to Standby.

You can adjust individual speaker levels while listening

to an input source. These temporary adjustments are can-

celled when the TX-SR502/TX-SR502E is set to

Standby.

Notes:

•You cannot use this function while the TX-SR502/

TX-SR502E is muted.

• Speakers that are set to No or None in the Speaker

Conﬁguration cannot be adjusted.

With the sleep timer you can set the TX-SR502/

TX-SR502E so that it automatically turns off after a set

period.

To cancel the sleep timer,

press the [SLEEP] button

repeatedly until the SLEEP indicator disappears.

To check the remaining sleep time,

press the [SLEEP]

button. Note that if you press the [SLEEP] button while

the sleep time is being displayed, you’ll shorten the sleep

time by 10 minutes.

You can connect a pair of stereo headphones (1/4-inch

phone plug) to the TX-SR502/TX-SR502E’s PHONES

jack for private listening, as shown.

Notes:

•Always turn down the volume before connecting your

headphones.

• Speaker sets A and B are turned off while the head-

phones plug is inserted in the PHONES jack.

• When you connect a pair of headphones, the listening

mode is set to Stereo, unless it’s already set to Pure

Audio, Stereo or Direct. When you disconnect the

headphones, the previous listening mode is selected.

• When the multichannel DVD input is selected, only

the front left and front right sounds can be heard in the

headphones.

Muting the TX-SR502/TX-SR502E

Press the remote controller’s

[MUTING] button.

The output is muted and the MUTING

indicator ﬂashes on the display, as

shown.

Adjusting Speaker Levels

Temporarily

Use the remote controller’s

[CH SEL] button to select each

speaker, and use the [LEVEL–]

and [LEVEL+] buttons to adjust

the volume.

Speakers are selected in the following

order: Left

→

Center

→

Right

→

Surr

Right

→

Surr Back

→

Surr Left

→

Subwoofer.

You can adjust the volume of each

speaker from –12 dB to +12 dB

(–15 dB to +12 dB for the subwoofer).

The name of the currently selected

speaker and its volume appear on the

display, as shown.

MUTING

CH SEL

LEVEL

Using the Sleep Timer

Press the [SLEEP] button repeat-

edly to select the required sleep

time.

You can set the sleep time from 90 to 10

minutes in 10 minute steps.

The SLEEP indicator appears on the

display when the sleep timer has been

set, as shown. The speciﬁed sleep time

appears on the display for about ﬁve

seconds, then the previous display

reappears.

Using Headphones

SLEEP

SLEEP indicator

STANDBY/ON

POWER

PHONES

OFFON

SPEAKERS BA

TX-SR502_En.book Page 39 Tuesday, February 17, 2004 12:14 PM

1 2 ... 34 35 36 37 38 39 40 41 42 43 44 ... 59 60

Comments to this Manuals

No comments

Audiovox D2016 - DVD Player - 10.2 Instruction Manual Page 39

Comments to this Manuals

Related products and manuals for AV receivers Audiovox D2016 - DVD Player - 10.2