Audiovox AFX-35.00 Installation Manual download pdf (Page 5)

128-8971a

5 of 32

This Remote Start/Alarm System is designed to be used with Automatic Transmission- Fuel Injection

Gas or Diesel Vehicles Only!

INSTALLATION OF THE MAJOR COMPONENTS:

CONTROL MODULE: PART # 1365186

Select a mounting location inside the passenger compartment (up behind the dashboard). The mounting

location selected must be within 24" of the ignition switch wiring harness to allow connection of the 6 pin

main wiring harness. Be certain that the chosen location will not interfere with proper operation of the

vehicle. Avoid mounting the module to or routing the wiring around the steering shaft/column, as the

module or wiring may wrap around or block the steering wheel preventing proper control of the vehicle. The

module will be secured after all wiring is completed which will allow complete access until the job is done.

Do Not Mount The Module In The Engine Compartment, as it is not waterproof.

HOOD PIN SWITCH: PART # 1363699

The pin switch included in this package is intended for protecting the hood area of the vehicle. In all cases,

the switch must be mounted to a grounded metal surface. When the pin switch is activated, (hood open),

it will supply a ground to the input wire activating the alarm. In addition, the hood switch is required for the

safety shut down of the remote start unit. If the vehicle is being worked on, this hood switch prevents the

remote start activation even if the RF command to start is issued. This switch must be installed in all

applications. Failure to do so may result in personal injury or property damage.

THE PUSH-BUTTON/PROGRAM SWITCH/LEDASSEMBLY: PART #PRLED

Select a mounting location known and accessible to the operator of the vehicle. A dash knockout plug or

front dash panel is desirable as the now Push-Button LED assembly needs the LED to be visible from the

outside of the vehicle and will be used for valet modes, programming features, programming transmitters,

and for overriding the remote start unit when the vehicle is being serviced. Inspect behind the chosen

location to insure that adequate clearance is allowed for the body of the switch, and also that the drill will

not penetrate any existing factory wiring or fluid lines. Drill a 5/16" or 8mm hole in the desired location and

mount the switch by passing the connectors, one at a time, through the panel from the front side and

pressing on the bezel until the switch is fully seated.

SHOCK SENSOR: PART # AS9492a

Select a centrally located, solid mounting surface for the shock sensor that will allow consistent operation

from all areas of the vehicle. The selected location must be within 18" of the control module to allow routing

and connecting of the 4 pin harness. Secure the shock sensor to the chosen location using two #8 self

tapping sheet metal screws. The sensor can also be secured to an existing dash brace using cable tie

straps. Whichever mounting method is used be sure to allow access to the sensitivity adjustment poten-

tiometer for use later in the installation.

STARTER INHIBIT RELAY: PART # 1363731

Select a mounting location within 12" of the ignition switch's low current start solenoid wire. Secure the

relay to an existing harness in the chosen location using a cable tie around the relay's wiring harness.

CAUTION! Do not wire tie the metal bracket to an existing wiring harness as vibration may cause

chaffing and shorting damaging the factory wiring. If an existing harness is not available

then secure the relay's metal mounting tab to an under dash metal brace with a #8 self

tapping sheet metal screw. Wire the relay as per the diagram found later in this manual.

This unit is to be used in vehicles with AUTOMATIC TRANSMISSIONS only! Although this combination

Alarm/Remote Start unit is a sophisticated system with many advanced features, IT MUST NOT be

installed into a vehicle with a manually operated transmission. Doing so may result in serious

personal injury and property damage.

1 2 3 4 5 6 7 8 9 10 ... 31 32

Comments to this Manuals

No comments

Audiovox AFX-35.00 Installation Manual Page 5

Comments to this Manuals